Xdax rumlogng voice keyer manual#
Xdax rumlogng voice keyer windows#

The ULI provides two PTT outputs one for the rig via the ACC2 connector and another for the sequencer via a 3.5mm plug on the back of the ULI. There are two PTT sources N1MM via the RS-232 cable and a foot switch. LPT1 - Select CW/PTT (Not really needed.) Under Config/Config Ports/Hardware - COM2, Radio is Kenwood. Select CW/PTT.ĬOM1 goes to the TS-2K for CAT control. Under Config/Config Ports/Hardware - COM1, Radio is None, SET - PTT is selected. Note - CAT PTT doesn't work with the audio lines on ACC2 Set up LPT1 to do PTT as well.ĬOM1 goes to the ULI and controls the PTT. Use COM1 for the PTT on ACC2 via the ULI. You need to do at least three things in N1MM set up the COM Ports, take care of the PTT and configure the SSB messages.Ĭom settings. Control Panel/Sounds/Scheme - Choose: No Sounds.

Otherwise, you'll get a 'Ding' during a transmission when you click on the wrong thing.

Xdax rumlogng voice keyer windows#

Make sure the windows sounds are turned off. This panel allows you to select and adjust the volume for the program input.ġ) Options/Properties enable these sliders: Line-In and Microphone.Ģ) Under Microphone, enable the +20db Mic Boost.ģ) Select the Microphone and set the slider at 100%. This is the one to use for the WinWarbler. Adjust the output of the ULI with the Mic Gain knob on the front panel. Adjust the Microphone slider to about 80% I used an extender cable so the female connection was near the rig. So the Line-In is muted.Ĭonnect the Heil microphone on the headset to the Microphone input connector on the sound card. For N1MM, we don't really need this connection because we don't care about the received audio. RX audio originates on the TS-2K ACC2 connector, goes through the ULI and then to the Line-In on the sound card.

Do the following:ġ) Options/Properties enable these sliders: Play Control, Wave, Line-In and Microphone.Ģ) Under microphone advance, enable the +20db Mic Boost. The Play control modifies the volume settings as they leave the computer. To reduce some of the confusion, I enabled only the sliders I need. There are two control panels and they are confusing. ULI RJ-45 TS-2K RX/TX/PTT to ACC2 (Must use PTT on ACC2 to use these audio lines) SC Line Out ULI Spkr Audio from the computer to the ULI You will also need to do something special for the footswitch, PTT and sequencer.ĬOM2 TS-2K Belkin USB-Serial Adapter - provides CAT control via RS-232 My experiment shows these lower cost devices can be used, but the trade off is a whole bunch of cabling. Of, if you don't mind all the cables, use one of the cheaper variants. (HH -> TS-2K -> computer -> Internet -> Computer -> Alaska) The web site is terrible and it looks like the guys are done with the project. I was able to work somebody in Alaska from my handheld, while sitting in my Lazyboy. It was built for running echolink and it worked well for that project. The ULI is an audio interface device I bought at the Dayton Hamfest several years ago.

ULI Schematic (large ~400k) the only thing really useful from their docs.

New Wire Diagram using the ULI - allows N1MM to function as a voice keyer.

Old Wire Diagram using the ULI - used for digital modes, shows ACC2 connector.

Wire Diagram of the 440 Contest Station using the TS-2000 and the MicroKeyer.

The second station can enter the call, press the space bar and all the info will be entered automatically - including the bearing info.

After first station logs the call, he can pass by clicking on the 'pass' button.

Xdax rumlogng voice keyer manual#

Set up a function key to pass all the info to another station (look in N1MM manual for macro example).

Enter the grid in the grid window, press space - will calculate the bearing.

ALT-= enter grid and press ALT-= to search for other Q's within that grid.

Setting the audio levels and using the proper audio control panel can be time consuming.Ģ) Configure the COM Ports in N1MM for PTT and CATģ) Configure N1MM to use your audio card and the appropriate inputsģ) Pre-record the letters and numbers using AudacityĬTRL-SHIFT-Fx - record message for function Fx (toggle) I used an audio editor called Audacity to make the letters/numbers wav files, which can be found at: A cheap audio interface can be used, but there are a lot of cables. This can be adapated to fit any of the other rig interfaces. Here are my notes for setting up N1MM with my Ulitmate Linking Interface (ULI) and my TS-2000. CQ,) it will say the callsign of the station you're working using individual recordings of the letters and numbers. Not only will it play pre-recorded messages (e.g. N1MM can be used as a digital voice keyer.